Baltimore County's Dedicated Generac Specialists

Generac Generator Problems: 7 Common Issues & Fixes

The short answer: most Generac problems are small, predictable, and maintenance-related — a dead battery, a closed fuel valve, or a missed service — and the controller usually tells you exactly what's wrong. The fix is often a 5-minute check you can do yourself. The expensive mistakes are ignoring a fault code until storm season and touching gas or line-voltage parts that are technician-only. Here's the honest rundown.

  • Licensed & InsuredMaryland MHIC
  • Generac SpecialistsAll we do
  • 24/7 RepairEmergency response
  • Free EstimatesOn installations

Prefer to talk? (443) 499-2549

Get your free quote

60-second form — a specialist replies within 1 business hour. No obligation; your info stays private.

A standby generator is a machine that sits idle for months and is then asked to run perfectly, in the worst weather, at 2 AM. When it doesn't, the failure is rarely mysterious. After years of servicing Generac units across Baltimore County, the pattern is consistent: most problems trace back to the battery, the fuel supply, or skipped maintenance — in that order — and the controller's fault code usually points straight at the cause.

Start every diagnosis the same way: read the controller. It shows plain-language status and, on most models, a fault code or warning — Low Battery, Overcrank, Overspeed, Low Oil Pressure, RPM Sense Loss — that narrows "the generator doesn't work" down to one system. Write down the exact message before you reset anything; a fault that follows every exercise cycle is a different problem from one that appeared once after a long outage.

Generac problems at a glance

SymptomLikely causeSafe homeowner checkCall a technician when
Won't start at allDead or weak battery (most common)Controller on Auto? Emergency stop in Run? Battery over 3 years old?New battery doesn't fix it, or the controller is blank
Cranks but won't fireFuel delivery — closed valve, empty propane tank, regulator pressureFuel valves fully open? Propane tank level? (Overcrank / error 1100)Fault returns after one reset, or you smell gas
Starts, then shuts downLow oil, overload, or a sensor faultRead the fault code; check for leaks or blocked ventsLow-oil, overspeed, or repeated shutdown faults
Runs but the house has no powerTransfer switch not transferringCheck visible breaker positions only if you understand the panelAny transfer-switch diagnosis or wiring issue — always
Fault code on the displayDepends on the code (see below)One reset: Off, wait 30 seconds, back to AutoThe same code returns immediately
Runs rough or overheatsClogged air filter, blocked airflow, overdue oil serviceClear leaves and debris from vents and the intakeRough running persists, or oil is low with no visible leak
Exercise cycle fails or alarmsWeak battery, failing charger, or a stuck exercise timerCheck the exercise schedule and any Low Battery warningCharger-related faults or repeated exercise failures

Fault-code meanings vary by controller and model — confirm against your owner's manual or the spec sheet for your exact unit. Never treat a code as a repair instruction by itself.

The 7 most common Generac generator problems, in detail

1. A dead or dying battery. The number one cause of Generac no-starts, ahead of fuel and controller faults. Most starter batteries last just 2–3 years, and unlike a car battery they give almost no warning — the first symptom is usually silence during an outage. A healthy battery reads near 12.6 volts at rest and shouldn't sag below roughly 10 volts while cranking. Replace proactively at year three; see our battery replacement guide for costs and warning signs.

2. Overcrank / fuel delivery failure (error 1100). The engine cranks but never fires, then the controller gives up and logs an overcrank fault. The cause is almost always fuel: a shutoff valve someone closed during service and never reopened, an empty propane tank, or a regulator delivering the wrong pressure after a temperature swing. Confirm the valves are fully open and the tank has fuel, reset once, and stop there if it comes back — repeated cranking floods the engine and won't fix a fuel problem.

3. Starts, then shuts down. Low oil pressure (error 1300) is the usual suspect — either the oil genuinely is low or the pressure sensor has failed — followed by overload (error 2100), when the load exceeds the unit's rated capacity. Check the oil level first, then the fault code. If the unit is overloaded, the fix is load management or a proper sizing review, not a bigger breaker.

4. RPM sense loss (error 1505). The controller can't sense engine speed, so it can't manage startup and load. A blank control panel when you try to start points to a dead battery; a persistent 1505 with a good battery can be a controller firmware issue, which a certified technician updates. Starter replacement is a last resort here, not a first guess.

5. The generator runs, but the house stays dark. This is a transfer-switch problem, not a generator problem — the unit is producing power that never reaches your panel. Check only the visible breaker positions, and only if you understand the panel and nothing looks damaged. Everything inside the transfer switch is line voltage and technician-only; never remove its deadfront.

6. Overheating, rough running, or a shutdown under load. Air-cooled Guardians live outdoors, and a clogged air filter, leaves packed against the intake, or a nest in the enclosure will starve the engine of air and trip a shutdown — especially on the first hot, humid run of summer. Clear debris from the vents, keep the pad clear, and treat a recurring overheat as a service call, not a cleaning job. Overdue oil changes cause the same symptoms for a different reason: follow the maintenance schedule and it mostly doesn't happen.

7. Charger and exercise failures. The built-in trickle charger keeps the battery topped up while utility power is present — but a failing charger board will quietly let a new battery die within weeks, often surfacing as a "Low Battery" warning after every weekly exercise. Turning the unit off mid-outage can also trigger a charger-missing-AC fault (error 2200). If charger-related faults keep returning, the charger itself needs diagnosing; a new battery on a dead charger is money wasted.

Why generator problems hit harder in Baltimore County

Baltimore County's outage pattern is what turns a small fault into a big problem. Nor'easters, summer thunderstorms, and ice storms knock BGE lines down with little warning, and the outages that matter most arrive in the worst weather — exactly when a cold-weakened battery cranks hardest and a marginal fuel system is under the most strain. Hot summers age batteries faster and cold snaps cut their cranking capacity, so a county battery lives a harder life than the same battery in a mild climate.

The stakes are higher here than in a typical suburb, too. In north-county towns like Kingsville, Monkton, and Sparks, many homes run on well pumps and septic systems — a generator that won't start means no water at all. Along the water in Essex, Dundalk, and Edgemere, a dead generator during a coastal storm can mean a sump pump that stops while the water is still rising. In dense suburbs like Parkville and Perry Hall, whole streets lose power together, so the technician queue during a widespread outage is long — a fault fixed in advance beats a fault fixed in a storm.

One local note: any repair that touches the gas line — a regulator swap, a fuel-valve replacement, a gas leak — is permitted work in Baltimore County, routed through the Department of Permits, Approvals, and Inspections, and it's technician-only for safety as well as code. The same goes for a natural-gas meter check with BGE if your unit is starving for fuel on utility gas. The five-minute checks in this guide — Auto mode, emergency stop, valves, vents, fault codes — are the homeowner's lane. Everything past that is ours, and that's what 24/7 generator repair is for.

Generac generator problems, answered

Why won't my Generac generator start?

The most common reason is the starter battery: most Generac batteries last just 2–3 years, and a weak one will crank slowly or not at all. Before calling anyone, check that the controller shows Auto (not Off or Manual), the emergency stop switch is in the Run position, and the fuel shutoff valves are open. If it cranks but won't fire, the problem is usually fuel delivery — a closed valve, an empty propane tank, or a regulator issue. If it won't start after those checks, note any fault code on the display and call a technician rather than cranking it repeatedly.

What does the overcrank error mean on a Generac?

Overcrank (error 1100 on most controllers) means the engine cranked for its programmed window — typically about two minutes of crank-and-pause cycles — without starting. It almost always traces back to fuel: a closed shutoff valve, an empty propane tank, or a fuel regulator delivering the wrong pressure. Check the valves and the tank level first, then reset once (Off, wait 30 seconds, back to Auto). If the overcrank returns, stop resetting and call a technician — repeated cranking won't fix a fuel problem and can flood the engine.

Can I reset a Generac fault code myself?

Yes, for a one-time reset: switch the controller to Off, wait 30 seconds, then switch it back to Auto. That clears nuisance alarms after a power flicker. But if the same fault comes straight back, do not keep resetting — write down the exact code and call a technician. Never open gas lines, adjust a regulator, bypass a safety, or remove the deadfront of the transfer switch: fuel work and line voltage are technician-only, and clearing a code does not fix the condition that caused it.

How much does it cost to fix a Generac generator?

The most common fix is also the cheapest: a new starter battery typically costs $100–$300, and a professional replacement usually runs in the low hundreds all-in, including a charger check and a start test. Sensors, regulators, and fuel-system parts vary by model and are diagnosed and priced per repair — a technician can usually quote after a single visit. The expensive outcome is a problem ignored until storm season: a failed start during a widespread outage means a long wait for a technician, so fixing a fault when it first appears is almost always the cheaper path.

Proudly serving Baltimore County

From Towson to Essex, Dundalk to Monkton — wherever you are in the county, a Generac specialist is close by.

24/7 Emergency Repair

Generator down? We respond fast.

A dead generator during a storm is an emergency — and we treat it like one. Call any time, day or night, and a Baltimore County Generac technician will get your backup power back online.

  • Generator won't start
  • Flashing red or yellow error codes
  • Transfer switch won't transfer power
  • Storm or power-surge damage
  • Runs rough, surges, or shuts off

Same-day & after-hours emergency response across Baltimore County.

(443) 499-2549

Mon–Sat: 9:00 AM – 5:00 PM · Sun: Emergency Service Only

Let's keep your home powered.

Free estimates on installations. 24/7 emergency repair. One county, one specialty: Generac.

Talk to a Generac Specialist — (443) 499-2549